TM
11-6125-240-34
REFERENCE
DESIGNATION
NOMENCLATURE
Semiconductor 1543026-2 (mfd by 83298)
CR5
CR6
Semiconductor 1549913-2 (mfd by 83298)
CR7
Semiconductor 1549913-2 (mfd by 83298)
CR8
Semiconductor 1549913-2 (mfd by 83298)
CR9
Semiconductor 819782-22 (mfd by 83298)
CR10
Semiconductor 1549813-2 (mfd by 83298)
CR11
Semiconductor 819782-26 (mfd by 83298)
Q1
Transistor 2N3251
Q2
Transistor 2N3251
Q3
Transistor 1544412 (mfd by 83288)
Q4
Transistor 2N2907A
Q5
Transistor 1544542 (mfd by 63298)
Q6
Transistor 2N3772
Q7
Transistor 2N2907A
Q8
Transistor 1544542 (mfd by 83298)
Q9
Transistor 1545643-3 (mfd by 83288)
Q10
Transistor 2N3251
Q11
Transistor 2N3772
R1
Resistor 10 K ohm 1/8 W
R2
Resistor 37.4 K ohm 1/4 W
R3
Resistor 10 K ohm 1/8 W
R4
Resistor 24.9 K ohm 1/8 W
R5
Resistor 10 K ohm 1 W
R6
Resistor 1 K ohm 1/8 W
R7
Resistor 499 ohm 1/2 W
R8
Resistor 1 K ohm 1/8 W
R9
Resistor 10 K ohm 1/8 W
R10
Resistor 100 ohm 1/8 W
REFERENCE
Resistor 12.1 K ohm 1/8 W
R11
DESIGNATION
NOMENCLATURE
R12
Resistor 15 K ohm 1/8 W
R13
Resistor 2 K ohm 1/8 W
C1
Capacitor 0.047 uf, 100V
R14
Resistor 2490 ohm 1/8 W
C2
capacitor 1.5 uf, 20V
R15
Resistor 750 ohm 1/8 W
C3
Capacitor 1 uf, 35V
R16
Resistor 2 K ohm 1/8 W
C4
Capacitor 10 uf, 20V
R17
Resistor 6810 ohm 1/8 W
C5
Capacitor 0.22 uf, 400V
R18
Resistor 10 K ohm 1/8 W
C6
Capacitor 1 uf, 35V
R19
Resistor 26.1 K ohm 1/8 W
C7
capacitor 4.7 uf, 10V
R20
Resistor 49.9 K ohm 1/8 W
C8
Capacitor 0.22 uf, 35V
Resistor 4880 ohm 1/8 W
R 21
C9
Capacitor 0.01 uf, 200V
R22
Resistor 3010 ohm 1/8 W
CR1
Semiconductor 819782-22 (mfd by 83288)
R24
Resistor 3010 ohm 1/8 W
CR2
Semiconductor 1543026-2 (mfd by 83298)
R25
Resistor 69.8 K ohm 1/8 W
CR3
Semiconductor 819782-22 (mfd by 83298)
R26
Resistor 2 K ohm 1/4 W
CR4
Semiconductor 819782-22 (mfd by 83298)
R27
Resistor 37.4 K ohm 1/4 W
ELOIX020
Figure 4-12. Component Location and Polarity, 4B93-1-A.
CAUTION
the dimensions shown in chart below. After inserting
Do not touch leads with fingers or allow leads
lead wires through printed circuit board, cut wires, if
to become contaminated.
necessary, and bend as shown in A, figure 4-13. Draw
(4) Cut and form components leads (B, fig. 4-13) to
part firmly against circuit board and form wires for
4-24
