TM 9-6115-730-24
0057
INSTALLATION - Continued
4. If necessary, install lower front panel (Figure 1, Sheet 3, Item 40) using 7 washers(Figure 1, Sheet 3, Item
39), lockwashers (Figure 1, Sheet 3, Item 38), and bolts (Figure 1, Sheet 3, Item 37).
5. If necessary, install upper front panel (Figure 1, Sheet 3, Item 36) using 13 washers (Figure 1, Sheet 3, Item
35, lockwashers (Figure 1, Sheet 3, Item 34, and bolts (Figure 1, Sheet 3, Item 33).
6. If removed, install adapter (Figure 1, Sheet 2, Item 31) and 90 degree elbow (Figure 1, Sheet 2, Item 32) on
fuel tank (Figure 1, Sheet 1, Item 13). If removed, install 90 degree elbow (Figure 1, Sheet 2, Item 30) on fuel
solenoid valve (Figure 1, Sheet 2, Item 28). If removed, install 90 degree elbow (Figure 1, Sheet 2, Item 27)
and 90 degree elbow (Figure 1, Sheet 2, Item 26). Connect hose (Figure 1, Sheet 2, Item 25) to 90 degree
elbow (Figure 1, Sheet 2, Item 27) on fuel solenoid valve (Figure 1, Sheet 2, Item 28) and 90 degree elbow
(Figure 1, Sheet 2, Item 26) on auxiliary fuel pump (Figure 1, Sheet 2, Item 24).
7. If removed, install 90 degree elbow (Figure 1, Sheet 2, Item 23) on auxiliary fuel pump (Figure 1, Sheet 2,
Item 24). Connect hose (Figure 1, Sheet 1, Item 20) to 90 degree elbow (Figure 1, Sheet 2, Item 23) and to
90 degree bulkhead elbow (Figure 1, Sheet 1, Item 21) on fuel fill pocket (Figure 1, Sheet 1, Item 22).
8. If removed, install radiator (WP 0068).
9. Install washer (Figure 1, Sheet 2, Item 19), seal nut (Figure 1, Sheet 2, Item 18), nipple (Figure 1, Sheet 2,
Item 17), elbow fitting (Figure 1, Sheet 2, Item 16), and 90 degree male fitting (Figure 1, Sheet 2, Item 14) on
rear of fuel tank filler neck (Figure 1, Sheet 2, Item 15).
10. If removed, install elbow (Figure 1, Sheet 1, Item 12) to right side of fuel tank (Figure 1, Sheet 1, Item 13).
Connect hose (Figure 1, Sheet 1, Item 11) to 90 degree male fitting (Figure 1, Sheet 2, Item 14) at rear of fuel
tank filler neck (Figure 1, Sheet 2, Item 15) and to elbow (Figure 1, Sheet 1, Item 12). Install two hose clamps.
11. Install water separator filter drain (Figure 1, Sheet 1, Item 1) onto water separator filter (Figure 1, Sheet 1,
Item 3).
12. Install hose (Figure 1, Sheet 1, Item 8) onto water separator filter drain (Figure 1, Sheet 1, Item 1) using
clamp (Figure 1, Sheet 1, Item 7).
13. Install swivel ball fitting (Figure 1, Sheet 1, Item 6) onto hose (Figure 1, Sheet 1, Item 8) using clamp (Figure
1, Sheet 1, Item 7).
14. Install female connector (Figure 1, Sheet 1, Item 9) onto swivel ball fitting (Figure 1, Sheet 1, Item 6).
15. Install hose (Figure 1, Sheet 1, Item 10) onto female connector (Figure 1, Sheet 1, Item 9) using clamp
(Figure 1, Sheet 1, Item 7).
16. Install hose assembly (Figure 1, Sheet 1, Item 4) onto fuel pickup tube assembly (Figure 1, Sheet 1, Item 5)
and water separator filter (Figure 1, Sheet 1, Item 3).
END OF TASK
END OF WORK PACKAGE
0057-8
