TM 9-6115-730-24
0057
REMOVAL - Continued
14. Disconnect hose (Figure 1, Sheet 2, Item 25) from 90 degree elbow (Figure 1, Sheet 2, Item 26) on auxiliary
fuel pump (Figure 1, Sheet 2, Item 24) and from 90 degree elbow (Figure 1, Sheet 2, Item 27) on fuel solenoid
valve (Figure 1, Sheet 2, Item 28). Disconnect hose (Figure 1, Sheet 2, Item 29) from 90 degree elbow
(Figure 1, Sheet 2, Item 30) on fuel solenoid valve (Figure 1, Sheet 2, Item 28) and adapter (Figure 1, Sheet
2, Item 31) on fuel tank (Figure 1, Sheet 1, Item 13). If necessary, remove 90 degree elbow (Figure 1, Sheet
2, Item 30), 90 degree elbow (Figure 1, Sheet 2, Item 32), and adapter (Figure 1, Sheet 2, Item 31).
15. If necessary, remove 13 bolts (Figure 1, Sheet 3, Item 33), lockwashers (Figure 1, Sheet 3, Item 34), and
washers (Figure 1, Sheet 3, Item 35) on left side of upper front panel (Figure 1, Sheet 3, Item 36).
16. If necessary, remove 7 bolts (Figure 1, Sheet 3, Item 37), lockwashers (Figure 1, Sheet 3, Item 38), and
washers (Figure 1, Sheet 3, Item 39) on lower front panel (Figure 1, Sheet 3, Item 40) to access fuel cooler
fuel lines.
17. Disconnect hose (Figure 1, Sheet 4, Item 41) from 45 degree adapter (Figure 1, Sheet 4, Item 42) on fuel
cooler (Figure 1, Sheet 4, Item 43) and from 90 degree elbow (Figure 1, Sheet 4, Item 44) on fuel filter
(Figure 1, Sheet 4, Item 45). If necessary, remove 45 degree adapter (Figure 1, Sheet 4, Item 42), 90 degree
elbow (Figure 1, Sheet 4, Item 44), and adapter (Figure 1, Sheet 4, Item 46).
18. At two locations on left side of engine, remove two screws (Figure 1, Sheet 4, Item 47), washers (Figure 1,
Sheet 4, Item 48), nuts (Figure 1, Sheet 4, Item 49), and loop clamp (Figure 1, Sheet 4, Item 50). Remove
two screws (Figure 1, Sheet 4, Item 51), lockwashers (Figure 1, Sheet 4, Item 52), and bracket (Figure 1,
Sheet 4, Item 53). Remove hose (Figure 1, Sheet 4, Item 41).
19. Disconnect hose (Figure 1, Sheet 4, Item 54) from fuel cooler (Figure 1, Sheet 4, Item 43) and from elbow
(Figure 1, Sheet 4, Item 55) on fuel tank (Figure 1, Sheet 1, Item 13). If necessary, remove elbow (Figure 1,
Sheet 4, Item 55).
END OF TASK
INSTALLATION
NOTE
Apply sealing compound to all male pipe threads before connecting.
Install tiedown straps as required.
1. If removed, install elbow (Figure 1, Sheet 4, Item 55) on fuel tank (Figure 1, Sheet 1, Item 13). Connect hose
(Figure 1, Sheet 4, Item 54) to elbow (Figure 1, Sheet 4, Item 55) and to fuel cooler (Figure 1, Sheet 4,
Item 43).
2. Position two loop clamps (Figure 1, Sheet 4, Item 50) on hose (Figure 1, Sheet 4, Item 41). At two places on
left side of engine, install bracket (Figure 1, Sheet 4, Item 53), two lockwashers (Figure 1, Sheet 4, Item 52),
and two screws (Figure 1, Sheet 4, Item 51). On each bracket, install loop clamp (Figure 1, Sheet 4, Item 50),
two washers (Figure 1, Sheet 4, Item 48), screws (Figure 1, Sheet 4, Item 47), and nuts (Figure 1, Sheet 4,
Item 49).
3. If removed, install adapter (Figure 1, Sheet 4, Item 46), 90 degree elbow (Figure 1, Sheet 4, Item 44) on fuel
filter (Figure 1, Sheet 4, Item 45) and 45 degree adapter (Figure 1, Sheet 4, Item 42) on fuel cooler (Figure 1,
Sheet 4, Item 43). Connect hose (Figure 1, Sheet 4, Item 41) to 90 degree elbow (Figure 1, Sheet 4, Item 44)
and to 45 degree adapter (Figure 1, Sheet 4, Item 42).
0057-7
