TM 9-6115-729-24
0071
REMOVAL
1. Ensure generator set is fully stopped, ENGINE CONTROL switch is OFF, Battery Disconnect Switch is OFF,
and DEAD CRANK SWITCH is OFF before proceeding.
2. Open right front door and left front door.
3. Remove air cleaner indicator (Figure 1, Sheet 1, Item 11) from air cleaner (Figure 1, Sheet 1, Item 13).
4. Remove two clamps (Figure 1, Sheet 1, Item 3) and collar (Figure 1, Sheet 1, Item 4) and reducing elbow
(Figure 1, Sheet 1, Item 5) from air cleaner (Figure 1, Sheet 1, Item 2) and restricted tap sleeve (Figure 1,
Sheet 1, Item 6).
5. Remove sensor (Figure 1, Sheet 1, Item 7) from restricted tap sleeve (Figure 1, Sheet 1, Item 6).
6. Remove two clamps (Figure 1, Sheet 1, Item 8) and hose (Figure 1, Sheet 1, Item 9) from restricted tap sleeve
(Figure 1, Sheet 1, Item 6) and OUT port fitting on crankcase ventilation filter (Figure 1, Sheet 2,
Item 10).
7. Remove clamp (Figure 1, Sheet 1, Item 11) and disconnect restricted tap sleeve (Figure 1, Sheet 1, Item 6)
from air vent hose (Figure 1, Item 12).
8. Remove clamp (Figure 1, Sheet 1, Item 13) and disconnect air vent hose (Figure 1, Sheet 1, Item 12) from
engine turbo.
9. Remove two clamps (Figure 1, Sheet 1, Item 14) and hose (Figure 1, Sheet 1, Item 15) from IN port fitting on
crankcase ventilation filter (Figure 1, Sheet 2, Item 10) and engine crankcase filter adapter.
10. Remove two clamps (Figure 1, Sheet 2, Item 16) and disconnect hose (Figure 1, Sheet 2, Item 17) from swivel
fitting (Figure 1, Sheet 2, Item 18) on bottom of crankcase ventilation filter (Figure 1, Sheet 2, Item 10) and
from elbow (Figure 1, Sheet 2, Item 19) on right hand rear engine dipstick port.
11. Remove elbow (Figure 1, Sheet 2, Item 19), check valve (Figure 1, Sheet 2, Item 20) and adapter (Figure 1,
Sheet 2, Item 21) from right hand rear engine dipstick port.
12. Remove two fittings (Figure 1, Sheet 2, Item 22) from IN port and OUT ports on crankcase ventilation filter
(Figure 1, Sheet 2, Item 10).
13. Remove swivel fitting (Figure 1, Sheet 2, Item 18) from bottom of crankcase ventilation filter (Figure 1, Sheet 2,
Item 10).
14. Remove two screws (Figure 1, Sheet 2, Item 23), lockwashers (Figure 1, Sheet 2, Item 24), and washers
(Figure 1, Sheet 2, Item 25) to remover crankcase ventilation filter (Figure 1, Sheet 2, Item 10) from bracket
(Figure 1, Sheet 2, Item 26).
15. Remove two screws (Figure 1, Sheet 2, Item 27), lockwashers (Figure 1, Sheet 2, Item 28), and washers
(Figure 1, Sheet 2, Item 29), and spacers (Figure 1, Sheet 2, Item 30) to remove crankcase ventilation filter
bracket (Figure 1, Sheet 2, Item 26).
16. Remove air cleaner cover (Figure 1, Sheet 1, Item 31) by releasing four clamps (Figure 1, Sheet 1, Item 32).
17. Loosen nut (Figure 1, Sheet 1, Item 33) on each air cleaner mounting band (Figure 1, Sheet 1, Item 34) and
remove air cleaner (Figure 1, Sheet 1, Item 2).
0071-2
