TM 9-6115-730-24
0055
REMOVAL - Continued
4. Drill out two rivets (Figure 1, Sheet 1, Item 4), if necessary and remove dead crank plate (Figure 1, Sheet 1,
Item 5). Remove two screws (Figure 1, Sheet 1, Item 6), lockwashers (Figure 1, Sheet 1, Item 7), washers
(Figure 1, Sheet 1, Item 8), and switch plate (Figure 1, Sheet 1, Item 9) from air cleaner bracket (Figure 1,
Sheet 1, Item 10).
5. To remove terminal board TB5 (Figure 1, Sheet 1, Item 11), tag and disconnect wires from terminal board,
remove two nuts (Figure 1, Sheet 1, Item 12), screws (Figure 1, Sheet 1, Item 13), terminal board, and marker
strip (Figure 1, Sheet 1, Item 14).
6. To remove either switch CATSW1 (Figure 1, Sheet 1, Item 15) or switch CATSW2 (Figure 1, Sheet 1,
Item 16), tag and disconnect wires from switch, remove nut (Figure 1, Sheet 1, Item 17), lockwasher
(Figure 1, Sheet 1, Item 18), and switch.
7. To remove slave relay (SRY) (Figure 1, Sheet 1, Item 19), tag and disconnect wires from relay SRY, remove
screw (Figure 1, Sheet 1, Item 20), washer (Figure 1, Sheet 1, Item 21), lockwasher (Figure 1, Sheet 1, Item
22), and relay.
8. To remove starter motor magnetic switch (SMMS) relay (Figure 1, Sheet 1, Item 23), tag and disconnect wires
from SMMS relay, remove two screws (Figure 1, Sheet 1, Item 24), washers (Figure 1, Sheet 1, Item 25),
lockwashers (Figure 1, Sheet 1, Item 26), and SMMS relay.
9. To remove any of three spare fuses (Figure 1, Sheet 1, Item 27), pull fuse out of fuseholder (Figure 1, Sheet
1, Item 28). To remove spare fuseholder (Figure 1, Sheet 1, Item 28), remove two screws (Figure 1, Sheet 1,
Item 29), washers (Figure 1, Sheet 1, Item 30), insulators (Figure 1, Sheet 1, Item 31), and clips (Figure 1,
Sheet 1, Item 32).
10. To remove relay mounting track (Figure 1, Sheet 1, Item 33), remove two screws (Figure 1, Sheet 1, Item 34),
lockwashers (Figure 1, Sheet 1, Item 35), washers (Figure 1, Sheet 1, Item 36), and relay mounting track.
11. Two remove ammeter shunt R4 (Figure 1, Sheet 2, Item 37), tag and disconnect wires from shunt, remove
two screws (Figure 1, Sheet 2, Item 38) and shunt.
12. To remove diode D1 (Figure 1, Sheet 2, Item 39), tag and disconnect wires from diode, remove two screws
(Figure 1, Sheet 2, Item 40), lockwashers (Figure 1, Sheet 2, Item 41), washers (Figure 1, Sheet 2, Item 42),
insulator (Figure 1, Sheet 2, Item 43), and diode D1. Remove nut (Figure 1, Sheet 2, Item 44) and diode D1
(Figure 1, Sheet 2, Item 39) from insulator (Figure 1, Sheet 2, Item 43).
13. To remove any of three circuit breakers CB5 (Figure 1, Sheet 2, Item 45), CB4 (Figure 1, Sheet 2, Item 46), or
CB2 (Figure 1, Sheet 2, Item 47), remove two screws (Figure 1, Sheet 2, Item 48), lockwashers (Figure 1,
Sheet 2, Item 49), washers (Figure 1, Sheet 2, Item 50), and circuit breaker.
14. To remove CB5 CB4, or CB2 brackets (Figure 1, Sheet 2, Item 51), remove two screws (Figure 1, Sheet 2,
Item 52), lockwashers (Figure 1, Sheet 2, Item 53), washers (Figure 1, Sheet 2, Item 54), and bracket.
15. Remove three fuses F1, F2, or F3 (Figure 1, Sheet 1, Item 55), two nuts (Figure 1, Sheet 1, Item 56), two
screws (Figure 1, Sheet 1, Item 57), and fuseholder (Figure 1, Sheet 1, Item 58).
END OF TASK
0055-5
