TM 9-6115-730-24
0041
ASSEMBLY - Continued
7. Install seal (Figure 1, Sheet 4, Item 70), AUX FUEL switch (Figure 1, Sheet 4, Item 69), anti-rotation washer
(Figure 1, Sheet 4, Item 68), washer (Figure 1, Sheet 4, Item 67), and nut (Figure 1, Sheet 4, Item 66).
8. Install fuel level indicator (Figure 1, Sheet 4, Item 65), bracket (Figure 1, Sheet 4, Item 64), two lockwashers
(Figure 1, Sheet 4, Item 63), and nuts (Figure 1, Sheet 4, Item 62).
9. Install DVR adapter (Figure 1, Sheet 3, Item 61), ten screws (Figure 1, Sheet 3, Item 60), washers (Figure 1,
Sheet 3, Item 59), and locknuts (Figure 1, Sheet 3, Item 58).
10. If removed, install film (Figure 1, Sheet 3, Item 57) on custom alarm module (Figure 1, Sheet 3, Item 55).
Install gasket (Figure 1, Sheet 3, Item 56), custom alarm module (Figure 1, Sheet 3, Item 55), four washers
(Figure 1, Sheet 3, Item 54), and locknuts (Figure 1, Sheet 3, Item 53).
11. Install indicator light (Figure 1, Sheet 3, Item 52), washer (Figure 1, Sheet 3, Item 51), nut (Figure 1, Sheet 3,
Item 50), lamp (Figure 1, Sheet 3, Item 49), and lens (Figure 1, Sheet 3, Item 48).
12. Install seal washer (Figure 1, Sheet 3, Item 47), PARALLEL/UNIT switch (Figure 1, Sheet 3, Item 46), anti-
rotation washer (Figure 1, Sheet 3, Item 45), washer (Figure 1, Sheet 3, Item 44), and nut (Figure 1, Sheet 3,
Item 43).
13. Install seal (Figure 1, Sheet 3, Item 42), SYNC MODE switch (Figure 1, Sheet 3, Item 41), four screws
(Figure 1, Sheet 3, Item 40), knob (Figure 1, Sheet 3, Item 39), and screw (Figure 1, Sheet 3, Item 38).
14. Install DC ammeter (Figure 1, Sheet 3, Item 37), three screws (Figure 1, Sheet 3, Item 36), lockwashers
(Figure 1, Sheet 3, Item 35), and nuts (Figure 1, Sheet 3, Item 34).
15. Install seal (Figure 1, Sheet 3, Item 33), PANEL LIGHT switch (Figure 1, Sheet 3, Item 32), anti-rotation
washer (Figure 1, Sheet 3, Item 31), washer (Figure 1, Sheet 3, Item 30), and nut (Figure 1, Sheet 3, Item
29).
16. Install screw (Figure 1, Sheet 3, Item 28) and nut (Figure 1, Sheet 3, Item 27).
17. Install lamp (Figure 1, Sheet 3, Item 26), lens (Figure 1, Sheet 3, Item 25), panel light (Figure 1, Sheet 3,
Item 24), washer (Figure 1, Sheet 3, Item 23), and nut (Figure 1, Sheet 3, Item 22). Repeat for other two
panel lights.
18. Install three studs (Figure 1, Sheet 1, Item 3), washers (Figure 1, Sheet 2, Item 21), and retainers (Figure 1,
Sheet 2, Item 20).
19. Install holder (Figure 1, Sheet 1, Item 7), nut (Figure 1, Sheet 2, Item 19), and screw (Figure 1, Sheet 2,
Item 18).
20. Install two loop clamps (Figure 1, Sheet 2, Item 17), two washers (Figure 1, Sheet 2, Item 16), two screws
(Figure 1, Sheet 2, Item 15), and ten fuses (Figure 1, Sheet 2, Item 14).
21. Install seal (Figure 1, Sheet 2, Item 13), generator set control (GSC) (Figure 1, Sheet 2, Item 12), film
(Figure 1, Sheet 2, Item 11), six washers (Figure 1, Sheet 2, Item 10) and six locknuts (Figure 1, Sheet 1,
Item 9).
22. Install connector P7 and tighten screw on front of mating connector using 4mm Allen wrench.
END OF TASK
0041-10
