TM 9-6115-729-24
0056
REMOVAL
1. Ensure generator set is fully stopped, ENGINE CONTROL switch is OFF/RESET, Battery Disconnect Switch is
OFF, and DEAD CRANK SWITCH is OFF before proceeding.
2. Open left front doors, left rear doors, right front doors, and right rear doors.
NOTE
Cut tiedown straps as required.
3. Disconnect hose assembly (Figure 1, Sheet 3, Item 1) from elbow (Figure 1, Sheet 3, Item 2) on fuel pickup
tube assembly (Figure 1, Sheet 3, Item 3) and from elbow (Figure 1, Sheet 3, Item 4) on water separator filter
(Figure 1, Sheet 3, Item 5).
4. If necessary, remove elbow (Figure 1, Sheet 3, Item 2) and elbow (Figure 1, Sheet 3, Item 4).
5. Remove two hose clamps and disconnect hose (Figure 1, Sheet 1, Item 6) from elbow (Figure 1, Sheet 1, Item
7) on fuel tank (Figure 1, Sheet 1, Item 8) and from adapter (Figure 1, Sheet 1, Item 9) on tee (Figure 1, Sheet
1, Item 10) mounted on fuel tank filler neck (Figure 1, Sheet 1, Item 11).
6. Remove two hose clamps and disconnect hose (Figure 1, Sheet 2, Item 12) from elbow (Figure 1, Sheet 2,
Item 13) on tee (Figure 1, Sheet 2, Item 14) mounted on fuel tank (Figure 1, Sheet 1, Item 8) and from tee
(Figure 1, Sheet 1, Item 10) mounted on fuel tank filler neck (Figure 1, Sheet 1, Item 11).
7. If necessary, remove elbow (Figure 1, Sheet 2, Item 13), fitting (Figure 1, Sheet 1, Item 15), adapter (Figure 1,
Sheet 1, Item 9), seal nut (Figure 1, Sheet 1, Item 16), washer (Figure 1, Sheet 1, Item 17), and nipple (Figure
1, Sheet 1, Item 18).
8. Remove two hose clamps and disconnect hose (Figure 1, Sheet 3, Item 19) from male connector (Figure 1,
Sheet 3, Item 20) on tee (Figure 1, Sheet 2, Item 14) mounted on fuel tank (Figure 1, Sheet 1, Item 8) and from
elbow (Figure 1, Sheet 3, Item 21) mounted on fuel tank (Figure 1, Sheet 1, Item 8).
9. If necessary, remove male connector (Figure 1, Sheet 3, Item 20), tee (Figure 1, Sheet 2, Item 14), and elbow
(Figure 1, Sheet 3, Item 21).
10. Disconnect hose assembly (Figure 1, Sheet 3, Item 22) from elbow (Figure 1, Sheet 3, Item 23) on fuel tank
(Figure 1, Sheet 1, Item 8) and from fuel cooler (Figure 1, Sheet 3, Item 24). If necessary, remove elbow
(Figure 1, Sheet 3, Item 23).
11. Remove two clamps and disconnect hose assembly (Figure 1, Sheet 3, Item 25) from adapter (Figure 1, Sheet
3, Item 26) on regulator (Figure 1, Sheet 3, Item 27) at engine fuel return and from swivel elbow (Figure 1,
Sheet 3, Item 28) on fuel cooler (Figure 1, Sheet 3, Item 24).
12. If necessary, remove adapter (Figure 1, Sheet 3, Item 26), regulator (Figure 1, Sheet 3, Item 27), and swivel
elbow (Figure 1, Sheet 3, Item 28).
13. Disconnect hose assembly (Figure 1, Sheet 2, Item 29) from adapter (Figure 1, Sheet 2, Item 30) on fuel tank
(Figure 1, Sheet 1, Item 8) and from elbow (Figure 1, Sheet 2, Item 31) on auxiliary fuel pump (Figure 1, Sheet
2, Item 32). If necessary, remove adapter (Figure 1, Sheet 2, Item 30) and elbow (Figure 1, Sheet 2, Item 31).
14. Disconnect hose assembly (Figure 1, Sheet 3, Item 33) from elbow (Figure 1, Sheet 3, Item 34) on water
separator filter (Figure 1, Sheet 3, Item 5) and from elbow (Figure 1, Sheet 1, Item 35) on engine fuel pump.
0056-2
