TM 9-6115-730-24
0046
DISASSEMBLY - Continued
3. Remove two locknuts (Figure 1, Sheet 1, Item 2), six washers (Figure 1, Sheet 1, Item 3), four screws
(Figure 1, Sheet 1, Item 4), and turn load board (Figure 1, Sheet 1, Item 1) partly over.
4. Remove eight locknuts (Figure 1, Sheet 2, Item 5) and 16 washers (Figure 1, Sheet 2, Item 6), and tag and
disconnect wires from the rear of load board (Figure 1,sheet 2, Item6).
5. Tag and disconnect wires from rear of load board (Figure 1, Sheet 2, Item 12) terminals.
6. Tag wires from four varistors, V1 (Figure 1, Sheet 2, Item 7), V2 (Figure 1, Sheet 2, Item 8), V3 (Figure 1,
Sheet 2, Item 9), and V4 (Figure 1, Sheet 2, Item 10).
7. Remove eight jam nuts (Figure 1, Sheet 2, Item 11) and load terminals (Figure 1, Sheet 2, Item 12).
8. Remove four locknuts (Figure 1, Sheet 2, Item 13), four washers (Figure 1, Sheet 2, Item 14), two studs
(Figure 1, Sheet 2, Item 15), bus bar (Figure 1, Sheet 2, Item 16), and ground wire (Figure 1, Sheet 2,
Item 17).
9. Remove four locknuts (Figure 1, Sheet 2, Item 18), four screws (Figure 1, Sheet 2, Item 19), eight washers
(Figure 1, Sheet 2, Item 20), three bus bars (Figure 1, Sheet 2, Item 21), and bus bar (Figure 1, Sheet 2,
Item 22).
CAUTION
Note orientation of EMI filters (Figure 1, Sheet 2, Item 22) before removing.
10. Remove eight nuts (Figure 1, Sheet 2, Item 23), washers (Figure 1, Sheet 2, Item 24), screws (Figure 1,
Sheet 2, Item 25), varistors V1 (Figure 1, Sheet 2, Item 7), V2 (Figure 1, Sheet 2, Item 8), V3 (Figure 1,
Sheet 2, Item 9), and V4 (Figure 1, Sheet 2, Item 10), ground plate (Figure 1, Sheet 2, Item 26), and four
EMI filter assemblies (Figure 1, Sheet 2, Item 27).
END OF TASK
ASSEMBLY
CAUTION
Note orientation of EMI filters (Figure 1, Sheet 2, Item 22) before installing.
1. Install four EMI filter assemblies (Figure 1, Sheet 2, Item 27), ground plate (Figure 1, Sheet 2, Item 26),
varistors V4 (Figure 1, Sheet 2, Item 10), V3 (Figure 1, Sheet 2, Item 9), V2 (Figure 1, Sheet 2, Item 8), and
V1 (Figure 1, Sheet 2, Item 7), eight screws (Figure 1, Sheet 2, Item 25), washers (Figure 1, Sheet 2, Item
24), and nuts (Figure 1, Sheet 2, Item 23).
2. Install bus bar (Figure 1, Sheet 2, Item 22), three bus bars (Figure 1, Sheet 2, Item 21), eight washers
(Figure 1, Sheet 2, Item 20), four screws (Figure 1, Sheet 2, Item 19), and four locknuts (Figure 1, Sheet 2,
Item 18).
3. Install bus bar (Figure 1, Sheet 2, Item 16), two studs (Figure 1, Sheet 2, Item 15), four washers (Figure 1,
Sheet 2, Item 14), ground wire (Figure 1, Sheet 2, Item 17), and four locknuts (Figure 1, Sheet 2, Item 13).
4. Install eight load terminals (Figure 1, Sheet 2, Item 12), and jam nuts (Figure 1, Sheet 2, Item 11).
0046-4
