TM 9-6115-729-24
0054
INSTALLATION
NOTE
Install tiedown straps as required.
1. Install spare fuseholder (Figure 1, Sheet 1, Item 64), two screws (Figure 1, Sheet 1, Item 63), two nuts (Figure
1, Sheet 1, Item 62), and three spare fuses (Figure 1, Sheet 1, Item 61).
2. To install circuit breaker brackets (Figure 1, Sheet 3, Item 57) for CB5, CB4, or CB2, install bracket, two
screws (Figure 1, Sheet 3, Item 58), washers (Figure 1, Sheet 3, Item 59), and lockwashers (Figure 1,
Sheet 3, Item 60).
3. To install circuit breaker CB4 (Figure 1, Sheet 3, Item 52), install circuit breaker, two screws (Figure 1,
Sheet 3, Item 53), washers (Figure 1, Sheet 3, Item 54), lockwashers (Figure 1, Sheet 3, Item 55), and nut
(Figure 1, Sheet 3, Item 56).
4. To install circuit breaker CB5 (Figure 1, Sheet 3, Item 47) or CB2 (Figure 1, Sheet 3, Item 48), install circuit
breaker, two screws (Figure 1, Sheet 3, Item 49), washers (Figure 1, Sheet 3, Item 50), and lockwashers
(Figure 1, Sheet 3, Item 51).
5. To install diode D1 (Figure 1, Sheet 3, Item 42), install diode, insulator (Figure 1, Sheet 3, Item 46), two
lockwashers (Figure 1, Sheet 3, Item 45), washers (Figure 1, Sheet 3, Item 44), and screws (Figure 1,
Sheet 3, Item 43). Connect wires as tagged.
6. To install ammeter shunt R4 (Figure 1, Sheet 1, Item 40), install shunt and two screws (Figure 1, Sheet 1,
Item 41). Connect wires as tagged.
7. To install fuseholder track (Figure 1, Sheet 2, Item 36), install two screws (Figure 1, Sheet 2, Item 37),
washers (Figure 1, Sheet 2, Item 38), lockwashers (Figure 1, Sheet 2, Item 39), and track.
8. To install any fuseholder (Figure 1, Sheet 2, Item 31), install fuseholder, two insulators (Figure 1, Sheet 2,
Item 35), two clips (Figure 1, Sheet 2, Item 34), washers (Figure 1, Sheet 2, Item 33), and two screws
(Figure 1, Sheet 2, Item 32). Connect wires as tagged.
9. To install any of three fuses F1, F2, and F3 (Figure 1, Sheet 2, Item 30), push fuse into fuseholder (Figure 1,
Sheet 2, Item 31).
10. To install relay SMMS (Figure 1, Sheet 1, Item 25), install relay, two lockwashers (Figure 1, Sheet 1, Item 29),
lockwashers (Figure 1, Sheet 1, Item 28), and two screws (Figure 1, Sheet 1, Item 27). Connect wires as
tagged.
11. To install relay SRY (Figure 1, Sheet 1, Item 22), install relay, lockwasher (Figure 1, Sheet 1, Item 25), washer
(Figure 1, Sheet 1, Item 24), and screw (Figure 1, Sheet 1, Item 23). Connect wires as tagged.
12. To install either switch CATSW2 (Figure 1, Sheet 2, Item 19), or CATSW1 (Figure 1, Sheet 2, Item 18), install
switch, lockwasher (Figure 1, Sheet 2, Item 21), and nut (Figure 1, Sheet 2, Item 20). Connect wires as tagged.
13. Install jumpers (Figure 1, Sheet 1, Item 15) using screws (Figure 1, Sheet 1, Item 16) onto terminal board
(Figure 1, Sheet 1, Item 12). To install terminal board TB5 (Figure 1, Sheet 1, Item 12), install strip (Figure 1,
Sheet 1, Item 17), terminal board, two screws (Figure 1, Sheet 1, Item 14) and nuts (Figure 1, Sheet 1,
Item 13). Connect wires as tagged.
0054-7
