TM 9-6115-729-24
0040
DISASSEMBLY
1. Loosen screw on front of mating connector using 4mm allen wrench to disconnect connector P7 and remove
six locknuts (Figure 1, Sheet 2, Item 9), six washers (Figure 1, Sheet 2, Item 10), film (Figure 1, Sheet 2, Item
11), generator set control (GSC) (Figure 1, Sheet 2, Item 12), and seal (Figure 1, Sheet 2, Item 13).
2. Remove 10 fuses (Figure 1, Sheet 2, Item 14), two screws (Figure 1, Sheet 2, Item 15), two washers (Figure
1, Sheet 2, Item 16), and two loop clamps (Figure 1, Sheet 2, Item 17).
3. Remove screw (Figure 1, Sheet 2, Item 18), nut (Figure 1, Sheet 2, Item 19), and holder (Figure 1, Sheet 1,
Item 7).
4. Remove three retainers (Figure 1, Sheet 2, Item 20), washers (Figure 1, Sheet 2, Item 21), and studs (Figure
1, Sheet 1, Item 3).
5. Remove nut (Figure 1, Sheet 3, Item 22), washer (Figure 1, Sheet 3, Item 23), panel light (Figure 1, Sheet 3,
Item 24), lens (Figure 1, Sheet 3, Item 25), and lamp (Figure 1, Sheet 3, Item 26). Repeat for other two panel
lights.
6. Remove nut (Figure 1, Sheet 3, Item 27) and screw (Figure 1, Sheet 3, Item 28).
7. Remove nut (Figure 1, Sheet 3, Item 29), washer (Figure 1, Sheet 3, Item 30), anti-rotation washer (Figure 1,
Sheet 3, Item 31), PANEL LIGHT switch (Figure 1, Sheet 3, Item 32), and seal (Figure 1, Sheet 3, Item 33).
8. Remove three nuts (Figure 1, Sheet 3, Item 34), lockwashers (Figure 1, Sheet 3, Item 35), screws (Figure 1,
Sheet 3, Item 36), and DC ammeter (Figure 1, Sheet 3, Item 37).
9. Remove screw (Figure 1, Sheet 3, Item 38), knob (Figure 1, Sheet 3, Item 39), four screws (Figure 1, Sheet 3,
Item 40), SYNC MODE switch (Figure 1, Sheet 3, Item 41), and seal (Figure 1, Sheet 3, Item 42).
10. Remove nut (Figure 1, Sheet 3, Item 43), washer (Figure 1, Sheet 3, Item 44), anti-rotation washer (Figure 1,
Sheet 3, Item 45), PARALLEL/UNIT switch (Figure 1, Sheet 3, Item 46), and seal washer (Figure 1, Sheet 3,
Item 47).
11. Remove lens (Figure 1, Sheet 3, Item 48), lamp (Figure 1, Sheet 3, Item 49), nut (Figure 1, Sheet 3, Item 50),
washer (Figure 1, Sheet 3, Item 51), and indicator light (Figure 1, Sheet 3, Item 52).
12. Remove four locknuts (Figure 1, Sheet 3, Item 53), washers (Figure 1, Sheet 3, Item 54), custom alarm
module (Figure 1, Sheet 3, Item 55), and gasket (Figure 1, Sheet 3, Item 56). If necessary, remove film
(Figure 1, Sheet 3, Item 57).
13. Remove ten locknuts (Figure 1, Sheet 3, Item 58), washers (Figure 1, Sheet 3, Item 59), screws (Figure 1,
Sheet 3, Item 60), and DVR adapter (Figure 1, Sheet 3, Item 61).
14. Remove two nuts (Figure 1, Sheet 4, Item 62), lockwashers (Figure 1, Sheet 4, Item 63), bracket (Figure 1,
Sheet 4, Item 64), and fuel level indicator (Figure 1, Sheet 4, Item 65).
15. Remove nut (Figure 1, Sheet 4, Item 66), washer (Figure 1, Sheet 4, Item 67), seal (Figure 1, Sheet 4, Item
68), AUX FUEL switch (Figure 1, Sheet 4, Item 69), and seal (Figure 1, Sheet 4, Item 70).
0040-7
