TM 5-6115-365-15
C4
opposite the first appearance of each item is the total
quantity of items authorized for the number of
equipments supported. Subsequent appearances of the
same item will have no entry in the allowance columns
but will have in the description column a reference to the
first appearance of the item. Items authorized for use as
required but not for initial stockage are identified with an
asterisk in the allowance column.
(2)
The
quantitative
allowances
for
organizational level of maintenance represents one initial
prescribed load for a 15-day period for the number of
equipments
supported.
Units
and
organizations
authorized additional prescribed loads will multiply the
number of prescribed loads authorized by the quantity of
repair parts reflected in the appropriate density column
to obtain the total quantity of repair parts authorized.
(3)
Organizational
units
providing
maintenance for more than 100 of these equipments
shall determine the total quantity of parts required by
converting the equipment quantity to a decimal factor by
placing a decimal point before the next to last digit of the
number to indicate hundredths, and multiplying the
decimal factor by the parts quantity authorized in the 51-
100 allowance column. Example: Authorized allowance
for 51-100 equipments is 12; for 140 equipments multiply
12 by 1.40 or 16.80 rounded off to 17 parts required.
(4)
Subsequent changes to allowances will be
limited as follows: No change in the range of items is
authorized.
If
additional
items
are
considered
necessary, recommendation should be forwarded to
U.S. Army Troop Support Command for exception or
revision to the allowance list. Revisions to the range of
items authorized will be made by this Command based
upon engineering experience, demand data, or TAMMS
information.
g.
Thirty-Day DS/GS Maintenance Allowances.
(1)
The allowance columns are divided into
subcolumns: Indicated in each subcolumn, opposite the
first appearance of each item, is the total quantity of
items
authorized
for
the
number
of
equipments
supported. Subsequent appearances of the same item
will have no entry in the allowance column, but will have
in the description column a reference to the first
appearance of the item. Items authorized for use as
required but not for initial stockage are identified with an
asterisk in the allowance column.
(2)
The quantitative allowances for DS/GS
levels of maintenance will represent initial stockage for a
30-day period for the number of equipments supported.
(3)
Determination of the total quantity of parts
required for maintenance of more than 100 of these
equipments can be accomplished by converting the
equipment quantity to a decimal factor by placing a
decimal point before the next to last digit of the number
to indicate hundredths, and multiplying the decimal
factor by the parts quantity authorized in the 51-100
allowance column. Example: Quantity authorized
allowance for 51-100 equipments is 40; for 150
equipments multiply 40 by 1.50 or 60 parts required.
h.
One-Year Allowances Per 100 Equipments/
Contingency Planning Purposes. Indicates opposite the
first appearance of each item the total quantity required
for distribution and contingency planning purposes. The
range of items indicates total quantities of all authorized
items required to provide for adequate support of 100
equipments for one year.
i.
Depot
Maintenance
Allowance
Per
100
Equipments. Indicates opposite the first appearance of
each item the total quantity authorized for depot
maintenance
of
100
equipments.
Subsequent
appearances of the same item will have no entry in this
column, but will have in the description column a
reference to the first appearance of the item. Items
authorized for use but not for initial stockage are
identified with an asterisk in the allowance column.
j.
Illustration.
(1)
Figure number. Indicates the figure
number of the illustration in which the item is shown.
(2)
Item number. Indicates the callout
number used to reference the item in the illustration.
1-7. Special information
a.
Repair parts mortality has been based on 2000
hours of operation per year.
b.
Parts which require manufacture or assembly at
a level higher than that authorized for installation will
indicate in the source column the higher level.
Change 8 1-3
